06
2010
-
07
What is the function of steel balls in a ball mill?
Author:
Steel grinding balls are essential basic components of ball mills and are widely used in mining, cement plants, power plants, and other industries.
Grinding mill steel balls are critical basic components of ball mills and are widely used in mining, cement plants, power stations, and other industries. High- and low-chromium cast steel balls, as well as high- and low-chromium multi-element alloy castings and forgings, play a vital role in national economic development. In fact, certain special-material steel balls have been extensively applied across various sectors of the national economy, including high-chromium steel balls and forgings, low-chromium steel balls and forgings, forged steel balls with chromium-based linings, manganese-based linings, hammer heads, multi-element alloy steel balls, multi-element alloy linings, and a wide range of wear-resistant materials. The widespread adoption and application of these products have not only spurred the development of the ball-mill steel-ball manufacturing industry but have also promoted technological advancement and scientific progress in related sectors.
Requirements for the diameter of steel grinding balls loaded into a ball mill:
The output of a ball mill is influenced not only by the charge of steel balls but also by the diameter of the balls. It is essential to maintain a certain range of ball diameters and a specific proportion among balls of different sizes; typically, the ball diameters within the mill shell range from 25 to 60 mm. If the mill contains predominantly large-diameter balls, the impact force will be greater, which is advantageous for crushing large coal lumps. However, because the gaps between the balls are larger and the relative surface area is smaller, the compressive and grinding actions are weakened, adversely affecting both the mill’s output and the fineness of the pulverized coal. Conversely, if the mill contains too many small-diameter balls, the impact force will be reduced, leading to a decline in mill output; moreover, the increased relative surface area of the balls accelerates their wear, thereby raising the power consumption of the mill.
During operation, the grinding mill experiences continuous wear, causing both the weight and diameter of the steel balls to decrease. Therefore, new balls must be periodically added to maintain a consistent ball charge. Typically, larger-diameter balls are replenished, with the amount of replenishment determined based on the ball wear rate (the amount of ball wear per ton of coal ground) and the coal throughput. After the mill has operated for a certain period, the proportion of smaller-diameter balls within the mill shell increases. Consequently, it is generally necessary to shut down the mill after approximately 3,000 hours of operation to perform a ball-cleaning procedure, removing balls smaller than 15 mm and any broken balls, while simultaneously replenishing the ball charge with new balls.
Proper methods for using steel balls in ball mills:
A newly installed ball mill undergoes a break-in period. During this period, the initial charge of grinding media should constitute 80% of the mill’s maximum media capacity, with the proportion of each size class (Φ120 mm, Φ100 mm, Φ80 mm, Φ60 mm, and Φ40 mm) determined according to its respective size. The optimal media charge varies depending on the specific mill model; for example, the MQG1500×3000 ball mill has a maximum media capacity of 9.5–10 tonnes. For the first charge, large media (120 mm and 100 mm) should account for 30%–40%, medium media (80 mm) for 30%–40%, and small media (60 mm and 40 mm) for 30%.
Why is only 80% of the specified ball charge added during the break-in period of a ball mill? After the mill is installed, the large and small gears must be properly meshed, and the feed rate should be gradually increased. Once the mill has been running continuously and normally for two to three days, inspect the gear meshing. If everything is in order, open the manhole cover and add the remaining 20% of balls.
Note: The addition of small grinding balls is only required during the initial charging. During normal operation, the appropriate friction among the steel balls themselves, between the balls and the ore, and between the balls and the mill liners leads to increased wear, causing larger balls to break down into smaller ones and medium-sized balls to be reduced to fine particles. Therefore, under normal operating conditions, there is no need to add additional small balls. Small balls should only be added when the particle size of the valuable minerals has not yet achieved individual liberation and when the fineness of the grinding product fails to meet the requirements for flotation; in such cases, an appropriate amount of small balls may be added. Throughout operation, the steel balls in the ball mill continuously wear down. To maintain the desired ball charge filling ratio and an optimal ball size distribution, and to ensure stable mill operation, it is essential to replenish the balls appropriately to compensate for this wear.
The amount of steel balls added is determined by their mass; the quality of the steel balls, in turn, dictates the tonnage consumption rate for ore. It is best to use new-type wear-resistant steel balls.