08

2011

-

03

Introduction to Common Metallic Elements in Wear-Resistant Materials and Their Functions

Author:


Manganese: It is an austenite-forming element and also influences carbide formation. Excessive manganese can lead to the formation of austenite in the microstructure; however, austenitic microstructures are unsuitable for grinding balls because, under both dry and wet grinding conditions, such balls tend to fracture and spall extensively. Nevertheless, since manganese is used for deoxidation and desulfurization, its content in wear-resistant steel balls must not be too high.

Manganese: It is an austenite-forming element and also influences carbide formation. Excessive manganese can lead to the formation of austenite in the microstructure; however, austenitic microstructures are unsuitable for grinding balls because, under both dry and wet grinding conditions, such balls suffer substantial breakage and spalling. Nevertheless, since manganese is used for deoxidation and desulfurization, its content in wear-resistant steel balls must not be too high.

Carbon: The wear resistance of high-manganese steel castings does not increase indefinitely with increasing carbon content; rather, there is an upper limit. When the carbon content exceeds 1.4%, a large amount of carbides precipitates in the as-cast microstructure. During water-toughening treatment, these carbides cannot be completely dissolved into the austenite, and the interstitially dissolved carbon also reaches saturation. As a result, not only is wear resistance unaffected—indeed, it may even decline—but the material’s strength and toughness are reduced, making it prone to fracture during service.

Silicon: High silicon content reduces the solubility of carbon in austenite, leading to increased precipitation and coarsening of carbides at grain boundaries. After water toughening treatment, significant microstructural porosity remains at the grain boundaries; however, to completely eliminate this porosity, the silicon content in the steel should be controlled within the range of 0.4–0.6%. When the silicon content exceeds 0.8%, there is no significant impact on the various properties of high-manganese steel.

Manganese: High-manganese steels, owing to their high manganese content, exhibit an as-cast microstructure consisting of austenite and carbides. Following water quenching at approximately 1000°C—commonly referred to as “water toughening”—the vast majority of the carbides dissolve into the austenite, resulting in a microstructure composed of single-phase austenite or austenite with a small amount of residual carbides.

Sulfur: Due to the high manganese content in the steel, substantial amounts of MnS are formed and readily removed from the slag. Moreover, since the smelting is carried out in an alkaline slag, the sulfur content can be effectively reduced to below 0.03%. Such a low sulfur level has no significant adverse effect on the steel’s strength, toughness, or wear resistance.

Phosphorus: Phosphorus is rarely dissolved in steel in its elemental form; it typically exists at grain boundaries as Fe₂P and Fe₃P, significantly reducing the steel’s strength, toughness, and wear resistance. High carbon content further exacerbates the segregation of phosphorus to grain boundaries in the eutectic form. To ensure desired mechanical properties, the following relationship should be observed: C% = 11.27 − 2.761 × P%. In production, the phosphorus content must be controlled to ≤0.08%; for critical, complex, and thick-walled components, the limit is ≤0.07%.

Chromium: Chromium is a carbide-forming element. In addition to combining with carbon to form carbides, the remaining chromium dissolves in the matrix, thereby increasing the matrix’s electrode potential and enhancing its corrosion resistance. When the chromium content is relatively low, M3C-type carbides may form, leading to reductions in both hardness and toughness. Conversely, when the chromium content is high, the number of carbides increases markedly during solidification, resulting in a significant decline in toughness; at the same time, the reduced carbon content in the matrix lowers its hardness, thus diminishing wear resistance. However, some manufacturers have now adopted specialized production and heat-treatment processes to address this issue, enabling chromium contents as high as 30%.

Vanadium (and titanium): These two elements are naturally present in pig iron as trace alloying elements. They can form extremely hard carbonitrides that are uniformly dispersed throughout the matrix, thereby enhancing the matrix’s microhardness and wear resistance. In addition, they promote grain refinement.

Nickel (copper): Nickel (copper) is an austenite-forming element; increasing its content promotes the formation of austenite in the microstructure. In bainitic grinding balls, the primary function of adding nickel is to raise the matrix electrode potential and enhance corrosion resistance; however, excessive addition is economically inefficient, as even trace amounts are sufficient to achieve the desired effect.

Molybdenum: The primary functions of molybdenum are to refine the matrix, refine carbides, increase the electrode potential of the matrix, and enhance corrosion resistance. However, due to its high cost, its addition is not economically viable. Under metal-mold casting conditions, even a small addition can produce a significant effect, making it suitable for wear-resistant steel balls with special requirements.